Latex Paint Spraying Guide

Latex Paint Spraying Guide

Most of the time if you end up spraying latex you'll be painting interiors of homes It's often quite common to use airless sprayers for this purpose. Nonetheless, airless sprayers don't provide the identical high quality of end that you would be able to achieve with an HVLP Spray Gun. Additionally, an HVLP spray gun is more environment friendly at applying coating to a product’s surface. The downside to an HVLP spray gun is that it is going to be slower than an airless at finishing a given project. Ultimately, if your primary goal is achieving a high quality finish an HVLP spray gun is what you’ll most likely wish to use.

Challenges of using HVLP spray gun with latex paint
HVLP spray weapons use a high quantity of air at low pressure to atomize (break up) coating. The low pressure permits them to make use of less paint and be more environment friendly at applying a coating to a product surface. However, the low pressure that HLP spray gun makes use of could make it harder to interrupt up thicker coatings, including latex paints. To be able to successfully spray latex paint with an HVLP spray gun, a couple of things will have to be considered.

You'll need to use a high quantity air cap (high CFM) – high quality HVLP spray guns will include a variety of setups for the air cap as well because the fluid nozzle. The higher the quantity of air and air cap uses, the better it will be at being able to atomize heavier bodied coatings like latex paint.
If you will be using a turbine driven HVLP spray gun you will want to use a multistage turbine. The more stages that you could afford in your turbine unit, the better ability the unit could have in being able to spray latex paint. If you're considering between an HVLP spray gun and a turbine unit for latex painting projects, you may learn in regards to the differences between the two here.
Use a large fluid nozzle- For a pressure fed HVLP Spray Gun you will normally wish to use not less than a 1.8 MM Fluid Nozzle. For a Gravity Fed HVLP Spray Gun you'll typically want no less than a 2.zero or higher to be able to get the Latex Paint to flow. The big fluid nozzle will allow for the latex paint to circulate, smaller fluid nozzles will typically be hard to get Latex paint to move adequately.
Thinning-you’ll almost certainly have to thin the latex paint to be able to get it to adequately atomize. This is very true in case your utilizing a gravity fed HVLP Spray gun. You want to be sure that to make use of the manufacturer’s advisable thinner and only thin it the minimal quantity needed to get it to adequately spray.
If you don't want to use thinner, you’ll wish to consider using a pressure fed HVLP spray gun – pressure fed guns are available for HVLP spray weapons which might be fed by an air compressor. They are going to allow thicker coatings to be able to be equipped to the gun successfully and give higher management of the amount of coating you're supplying at a given time which will help in achieving better atomization despite the heavy bodied latex paint. You'll be able to learn more about pressure vs gravity vs suction fed spray weapons here.
When an HVLP spray gun is good for spraying latex paint
When your major goal is achieving a top quality end like when painting cabinets or trim
When you have got smaller areas to be painted that will not require a large volume of paint to cover the surface
When it's essential to preserve Overspray to a Minimal
Options to using an HVLP spray gun with latex paint
If you wish to be able to take care of high production but nonetheless achieve a finer end, you would potentially use an airless paint sprayer with a fine end tip. A Fine finish tip permits for higher atomization than a normal airless tip though won't yield the same end that an HVLP spray gun will.

Conclusion
should you’re taking a look at a project would require a fine finish and requires the application of latex paint and HVLP spray gun often is the perfect solution for you. To achieve the perfect result doable, you need to use a high quantity CFM air cap, thin the material an appropriate amount, consider utilizing a pressure fed system particularly if you will be utilizing a compressor fed HVLP spray can, and if you can be using a turbine driven HvLP spray gun it would be best to use a multistage system. By following the following pointers, you may be able to achieve a quality finish together with your latex paint project. For options on compressed air spray guns that might be excellent in your project you can contact us at the moment

If you beloved this article and you simply would like to be given more info regarding Latex laten spuiten please visit the website.